Description
Nuetech Nitrolube Cooling Gel - 150g Tube is a silicone-based mounting lubricant formulated to reduce friction and heat buildup in Nitromousse installations.
Key Features
- 150g tube
- Silicone-based formula developed for Nitromousse
- Reduces friction and disperses heat
- One tube is intended for one installation
Product Details
- Brand: Nuetech
- Manufacturer Part Number: NMLUBE150
- Product Type: Tire Mousse Lubricant
- Net Weight: 150g
Fitment and Use
Use during Nitromousse installation as directed. Do not substitute soap-based mounting paste; cover unused valve holes and follow current Nuetech lubrication instructions.
Nitro PROLINX Installation & Tuning
Install three full LINX, measure the gap, then cut the fourth to set your preferred tire feel. Follow the front or rear settings below.
Off-road use only. No street or highway use. Do not exceed 75 mph. Higher speeds can cause premature wear, damage, or failure.
Before you start
- Confirm fitment: Check your exact tire brand, model, size, and rim width in the Nuetech fitment guide. Identically marked tires can have different internal volumes. If the PROLINX match is unclear, confirm it with Nuetech before mounting.
- Use a working rim lock: A properly fitting, functioning rim lock is required to prevent tire slip.
- Seal lubricant escape paths: Check used tires for holes and plug them. Tape over unused rim holes.
- Review the supplied illustrated instructions: Watch Nuetech’s mousse mounting video for general mounting technique. Have a qualified shop install the mousse if you lack the correct tools or are not confident with the procedure.
1. Lubricate the tire
Squeeze the entire tube of supplied silicone-based lubricant in a thick bead along the inside crown of the tire, directly beneath the tread. It will distribute as you ride.
Never install PROLINX without proper silicone-based mousse lubricant. Do not substitute tire mounting paste.
2. Insert three full LINX
Place three uncut LINX inside the tire. Push the adjoining ends firmly together, leaving one gap for the fourth section.
3. Measure the remaining gap
Measure the gap at its shortest point, straight across the opening at the inside edge of the LINX.
Use a tape measure, or lay the fourth LINX beside the tire and mark the gap length on it as shown in the supplied diagram. The thin dotted marks are spaced 1 inch apart.
4. Calculate and cut the fourth LINX
Choose a setting and use the adjustment for your wheel. PSI values describe approximate tire feel, not air pressure. PROLINX is an airless mousse system.
| Setting | PSI feel | Front | Rear |
|---|---|---|---|
| Firm | 13–14 | +5 in. | +3 in. |
| Standard | 11–12 | +4 in. | +1 in. |
| Soft | 9–10 | +3 in. | −1 in. |
| Extra soft | 6–8 | +2 in. | −3 in. |
Start with the measured gap. Add inches for a plus (+) value or subtract inches for a minus (−) value. The result is the total length of the fourth LINX after cutting.
Examples with an 8-inch gap:
Firm front: 8 + 5 = 13 inches long.
Soft rear: 8 − 1 = 7 inches long.
Cut the fourth LINX to the calculated length using a large knife or fine-tooth hacksaw. Soapy water on the blade helps make a smoother cut; it does not replace mousse lubricant.
Optional ultra-low setup for hard enduro: Cut the fourth LINX 5 inches shorter than the measured gap. Nuetech specifies a full 10 minutes of riding for the LINX to elongate and space out.
5. Fit the fourth LINX and mount the tire
Fit the cut section into the tire and mount it using proper mousse installation technique. Position the rim lock at the center of a full-length LINX section.
If a long fourth section is difficult to seat, use the arrangement shown in Step 5 of the supplied illustrated instructions to press the raised ends into the tire.
Break-in, maintenance & storage
- Let the setup settle: Allow 2–3 heat cycles for break-in. Tire construction can change the pressure-equivalent feel by 2–3 psi. After break-in, add or remove mousse material as needed to fine-tune the feel.
- Re-lubricate when needed: Lubricant loss shortens mousse life. If lubricant leaks from the tire or rim, re-lubricate promptly. After high-speed use on hard off-road surfaces, remove, inspect, and re-lubricate the LINX after each day’s use.
- Monitor tire support: Mousse softens with use. Re-stuff or replace it before it becomes too soft or unstable. If instability develops while riding, slow to a controlled speed, stop safely, and inspect the mousse before continuing.
- Expect service life to vary: Speed, ambient temperature, riding intensity, and terrain affect how long PROLINX lasts.
- Store with both wheels raised: Use a stand when the bike is parked for extended periods to help prevent flat spots.
- Brand: Nuetech
- UPC: 857600007751